Battery negative terminal cable Citroën Peugeot 9816218080

€ 30.00

Stellantis CITROEN PEUGEOT
9816218080

1 disponibili

COD: 9980-P5_K18 Categorie: , , , Tag:

Descrizione

Negative battery cable for CITROEN, PEUGEOT and other Stellantis models

Part description

The used negative battery cable 9816218080 connects the negative terminal of the vehicle battery to the vehicle’s electrical ground. Reliable grounding is important for starting and for the proper operation of electrical accessories. Replacing a damaged cable may help resolve problems caused by a broken wire, corrosion or increased contact resistance at its connections.

This part is a suitable choice when repairing damaged battery wiring. When selecting a part, refer primarily to the product number 9816218080 and compare the cable design, terminals and mounting points with the original part. The model name alone is not enough to determine whether the design matches.

Technical information

  • Manufacturer: not specified; identified in the source materials as Stellantis / CITROEN / PEUGEOT.
  • Model: Citroën Berlingo K9, FIAT DOBLO III, OPEL COMBO E K9, PEUGEOT RIFTER, Toyota ProAce City.
  • Part type: negative battery cable.
  • Condition: used car part.
  • Catalog classification: 1.6 HDI, electrical components, wiring harnesses, engine wiring harnesses. The classification alone does not confirm suitability for a specific engine configuration.
  • Other numbers: not specified.

Product codes

  • Product codes: 9816218080.

Compare the number with the marking on the original part, if legible. Also check that the shape, length, connection points and any electrical connectors match.

Installation recommendations

The following procedure generally applies to this type of part. The exact access to the cable, mounting method, and procedure for disconnecting and reconnecting the battery depend on the specific vehicle model and configuration. Follow the manufacturer’s service instructions, especially the requirements for allowing the onboard electronics to enter sleep mode.

1) Before installation

  • Compare the product number, cable length and routing, terminal shape, connection lugs and mounting points with the original part.
  • Inspect the insulation along its entire accessible length. The cable must not have exposed wires, signs of overheating or damage around the terminals.
  • Check the terminal and lugs for corrosion, cracks and deformation. Check that the wires are not loose at the terminals.
  • If the wiring includes a connector or sensor, compare its design and check that it is intact. The source materials do not state whether this part includes these components.
  • Also check the condition of the battery terminal and the opposite contact surfaces. Installing a new cable will not fix a fault in a damaged connection point.

2) Tools and materials required

  • Hand tools suitable for the fasteners used and a torque wrench for tightening to the manufacturer’s service specifications.
  • Supplies for gently cleaning electrical contacts and a clean cloth.
  • Protective gloves, safety glasses and suitable insulating material to cover the disconnected lead.
  • A multimeter for checking electrical continuity and, if necessary, measuring voltage drop.

3) Step-by-step installation procedure

  1. Park the vehicle safely, switch off the ignition and all electrical accessories. Keep the key away from the vehicle.
  2. Allow the onboard electronics to enter sleep mode in accordance with the manufacturer’s instructions. Do not activate electrical systems unnecessarily while waiting.
  3. Gain access to the battery and cable routing. Before removal, take photos of the routing, mounting points and orientation of the terminals.
  4. Disconnect the battery according to the manufacturer’s procedure; on a conventional system, disconnect the negative terminal first. Secure the disconnected terminal to prevent accidental contact with the battery post.
  5. If the positive lead also needs to be disconnected, do so only after disconnecting the negative lead, and cover it securely. Prevent tools from bridging the battery terminals.
  6. Disconnect any other cable connections and connectors. After releasing the retaining clips, disconnect connectors by holding their housings, not by pulling on the wires.
  7. Release the cable from its clips and remove it carefully. Do not damage nearby wiring or mounting components.
  8. Clean the contact surfaces and inspect the fasteners. Resolve any significant corrosion or mechanical damage to the opposite contacts before installation.
  9. Position the replacement cable along the original route without tension, twisting or sharp bends. Secure it in the clips so that it cannot chafe or touch hot or moving parts.
  10. Attach the terminals away from the battery and connect any connectors. Tighten the connections to the manufacturer’s specifications; do not deform the terminals or lugs by applying excessive force.
  11. Reconnect the battery according to the manufacturer’s instructions. If both terminals were disconnected, on a conventional system reconnect the positive terminal first and the negative terminal last. Carry out any required procedures after restoring power.

4) Post-installation checks and function verification

  • Check that the terminal is seated securely, the connections are tight and the cable is routed safely.
  • Check that the vehicle starts and that the electrical accessories work. A professional measurement can be used to check the voltage drop on the negative lead under load in accordance with the service procedure.
  • After a short period of operation, check for the smell of overheated insulation or other signs of hot connections. If a fault is suspected, switch off the engine and do not drive the vehicle until the cause has been resolved.
  • If everything is in order, take a short test drive and then visually check that the cable remains properly secured.

5) Common installation mistakes and how to avoid them

  • Installing on corroded contacts: clean and inspect both contact surfaces before assembly.
  • Insufficient or excessive tightening: follow the service specifications to prevent a loose connection or a cracked terminal.
  • Incorrect routing: follow the original routing and use the designated clips so that the cable is not under tension or exposed to chafing.
  • Disconnecting the battery without allowing the electronics to sleep: follow the manufacturer’s procedure and do not work with the ignition switched on.
  • Confusing it with a similar-looking cable: compare the part number and all terminals and connections before installation.

Reasons why the part may become damaged

The following are common causes of damage to negative battery cables in general; they do not describe the condition of this specific part:

  • Corrosion of terminals and connection lugs caused by moisture and dirt, which worsens electrical contact.
  • Loose connections, which increase contact resistance and may cause localized heating.
  • Vibration and mechanical stress, especially if the cable is under tension or mounted incorrectly.
  • Chafing of the insulation against surrounding parts if a mounting clip is missing or damaged.
  • Rough handling when replacing the battery, such as prying at the terminal, pulling on the wire or overtightening.
  • Aging and thermal stress, which can cause the insulation to become brittle and weaken the wiring near the terminals.

Informazioni aggiuntive

Peso 0.6 kg

Se non diversamente indicato nella descrizione, tutte le foto sono a scopo illustrativo.

Ci riserviamo il diritto di sostituire la referenza ordinata con la referenza sostitutiva indicata dal produttore.

I ricambi provengono da veicoli sinistrati, sono accuratamente controllati e offriamo su di essi una garanzia di funzionamento per 12 mesi.