Descrizione
Multifunctional video screen for Stellantis vehicles
Some functions may need to be initialized using diagnostic equipment
Part description
The used radio and onboard computer display 98162661ZD is a multifunctional screen for the Citroën, Peugeot and Opel vehicles listed below. It displays information from the relevant onboard system; the specific range of functions depends on the vehicle’s equipment and configuration.
If you are dealing with an unreadable image, display interruptions or damage to the existing screen, replacing the display may be a suitable solution once the cause of the fault has been verified. When choosing a replacement, compare the product numbers, connectors and configuration of the original part. After installation, some functions may need to be initialized using diagnostic equipment.
Technical information
- Manufacturer: Stellantis – according to the supplied information.
- Model: Citroën Berlingo K9 | OPEL COMBO E K9 | PEUGEOT PARTNER III | PEUGEOT RIFTER.
- Part type: multifunctional video screen / radio and onboard computer display.
- Condition: used automotive part.
- Main product number: 98162661ZD.
- Additional numbers: 9828422080, 9830426480.
- Commissioning: some functions may require initialization using diagnostic equipment.
Product codes
- Product codes: 98162661ZD, 9828422080, 9830426480.
The numbers are listed in the information supplied for this product. Matching the vehicle model alone does not guarantee compatibility with every display variant; the correct configuration and compatibility with the onboard electronics are also important.
Installation recommendations
General information for this type of part: the following procedure is a general guide to replacing an automotive display. The precise removal of trim, mounting method and any required initialization depend on the specific vehicle model and equipment. Follow the manufacturer’s service procedure.
1) Before installation
- Compare the markings on the original and replacement parts, the shape of the housing, mounting points, and the number and type of connectors.
- Inspect the screen, housing, mounts and contacts. Check for cracks, bends, corrosion or moisture damage.
- First rule out a fault with the power supply, wiring or connected system. The display itself may not be the cause of a display failure.
- If possible, record the original settings and symptoms of the fault for comparison afterwards.
2) Tools and materials required
- Plastic tools for carefully removing trim.
- Hand tools suited to the fasteners used.
- A soft, clean work surface, a screen-cleaning cloth and protection for surrounding surfaces.
- Suitable diagnostic equipment to check the system and initialize functions if necessary.
3) Step-by-step installation procedure
- Park the vehicle safely, switch off the ignition and turn off electrical accessories.
- Allow the electronics to enter sleep mode and disconnect the battery according to the vehicle manufacturer’s procedure.
- Cover surrounding surfaces to prevent scratching them while working.
- Following the service procedure, remove the trim required to access the display. Do not use excessive force to overcome resistance from the clips.
- Release the original display’s fasteners and carefully slide it out far enough to avoid straining the wiring.
- Note the cable routing, release the connector locks and disconnect them by holding their housings, not the wires.
- Check the condition of the connectors and wiring. Resolve any damage before connecting the replacement part.
- Connect the matching connectors to the replacement display and check that their locking tabs are securely engaged.
- Position and secure the display without putting it under tension. Cables must not be pinched or routed over sharp edges. Refit the trim according to the service procedure.
- Restore the power supply according to the manufacturer’s instructions, check operation and perform diagnostic initialization if required.
4) Post-installation checks and function verification
With the vehicle stationary, check that the image is clear and stable, that the available controls respond, and that functions matching the vehicle’s equipment are displayed. Also check how the system behaves after it is switched off and back on. If any functions are missing, check the connections and whether initialization using diagnostic equipment is required. During any test drive, observe only the system’s normal operation; do not perform diagnostics or adjustments while driving.
5) Common installation mistakes and how to avoid them
- Choosing based only on the vehicle name: also compare the part numbers and physical configuration.
- Disconnecting while powered: follow the prescribed procedure for shutting down the electronics and disconnecting the battery.
- Damaging connectors or clips: release the locking tabs first and use suitable tools.
- Pressing on the display surface: handle the part by its housing and place it on a soft surface.
- Skipping initialization: limited functionality after replacement does not necessarily mean the display is faulty; some functions may require diagnostic configuration.
Reasons why the part may become damaged
Possible causes of damage to automotive displays in general include:
- Mechanical impact or excessive pressure on the screen and its housing.
- Moisture and ingress of cleaning products, which can damage the electronics or contacts.
- Prolonged exposure to temperature extremes and component ageing, which may cause reduced readability or intermittent image loss, for example.
- Power supply faults and electrical surges, which can affect electronic circuits.
- Improper removal, which can break mounting tabs, damage connectors or strain the wiring.
These are general causes and do not describe the condition of the item offered. Before replacing the display, it is important to address any external cause of the fault as well, so that it does not damage the replacement display.
