Handbrake control Citroën DS Peugeot 9813146377 98131463ZD

€ 36.00

Stellantis CITROEN PEUGEOT
9813146377 98131463ZD

1 disponibili

Descrizione

Electronic parking brake switch for CITROEN, PEUGEOT and other Stellantis models

Part description

This used electronic parking brake switch is used to send the command to activate and release the brake. It is a suitable solution when replacing a damaged or unresponsive switch. It is not the brake mechanism itself, but an electrical control component.

When looking for a replacement part, pay particular attention to the numbers 9813146377 and 98131463ZD. Before selecting, compare the numbers, connector, shape and mounting with the original switch. The model name alone may not be sufficient to select the correct version.

Technical information

  • Manufacturer: not specified; the documentation lists the designation Stellantis CITROEN PEUGEOT.
  • Model: Citroën Berlingo K9; FIAT DOBLO III; OPEL COMBO E K9; PEUGEOT RIFTER; Toyota ProAce City.
  • Other numbers: not specified.
  • Part type: electronic parking brake switch.
  • Category: electrical components – other controls and switches – parking brake.
  • Condition: used part.

Product codes

  • Product codes: 9813146377, 98131463ZD.

Both designations are listed in the documentation for this product. Comparing them with the designation on the original part is an important part of selecting a replacement.

Installation recommendations

The following procedure generally applies to this type of electrical switch. The exact method of access, removal and commissioning depends on the specific model and vehicle version. Follow the manufacturer’s service documentation; the switch is part of a safety-critical system.

1) Before installation

  • Inspect the body of the used switch, the control surface, mounting components and connector. Look for cracks, deformation, corroded contacts and signs of water ingress.
  • Compare the product numbers, shape, mounting and connector design with the old part.
  • Verify that the fault is actually related to the switch. A non-functioning parking brake may also be caused by the power supply, wiring or another part of the system.
  • Secure the vehicle against movement independently of the electronic parking brake.

2) Required tools and materials

  • Standard hand tools suitable for the fasteners used.
  • Plastic trim removal tools if the trim needs to be loosened.
  • A flashlight, clean cloth and, if necessary, a product suitable for cleaning electrical contacts.
  • Equipment to secure the vehicle against movement; suitable diagnostic equipment may also be needed, depending on the nature of the fault.

3) Step-by-step installation procedure

  1. Park the vehicle on a level, safe surface and secure it against unintended movement.
  2. Consult the service documentation to determine the prescribed parking brake state for switch replacement and the safe procedure for shutting down the electrical system.
  3. Switch off the ignition, follow the prescribed procedure for allowing the electronics to go to sleep and disconnecting the battery, as specified by the vehicle manufacturer.
  4. Carefully access the switch. If any covers or trim need to be removed, release them with suitable tools without forcing them.
  5. Before disconnecting, record the wiring route and connector orientation, for example by taking a photo.
  6. Release the connector lock and disconnect the connector by holding its body. Do not pull on the wires.
  7. Release the fasteners and remove the original switch without damaging the surrounding area or brackets.
  8. Compare the two parts and inspect the mating connector. If the contacts or wiring are damaged, rectify the fault first.
  9. Fit the replacement switch and secure it appropriately. The part must seat correctly without excessive force.
  10. Connect the connector until its lock engages and position the wiring so it is neither stretched nor pinched.
  11. Refit the removed covers, restore the power supply according to the manufacturer’s procedure and carry out the prescribed functional check.

4) Post-installation checks and test drive / functional verification

  • With the vehicle stationary and secured, first check its response to the command to activate and release the parking brake, as described in the vehicle owner’s manual.
  • Check the brake status indicator and any warning messages. A mechanical response from the button alone does not confirm that the entire system is working correctly.
  • Check that the switch is securely seated and that the control moves freely.
  • Only carry out a short test drive after the static check has been successful and the brake has been confirmed to be released correctly. Do not test the parking brake while driving.
  • If the response is unreliable or a fault message remains, do not use the vehicle until the cause has been rectified.

5) Most common installation errors and how to avoid them

  • Selecting a part based only on the vehicle model: also compare the part designation, connector and mounting.
  • Replacing the part without identifying the cause of the fault: check the power supply, connections and condition of the wiring beforehand.
  • Damaging clips and the connector: release the locks first and do not use excessive force.
  • Pinched wires or a connector that is not fully engaged: check their routing and ensure the connector is secured before refitting the trim.
  • Relying on the parking brake during repair: use an independent means of securing the vehicle against movement.

Reasons why the part may become damaged

In general, faults in this type of switch may occur for the following reasons; this is not a description of any damage identified on the item offered:

  • Mechanical wear of the control mechanism and contacts during prolonged use.
  • Ingress of liquids and dirt, which may cause sticking, corrosion or unreliable switching.
  • Excessive force or impact, resulting in a broken control component or mounting.
  • Careless removal, which may damage the clips, connector or its contacts.
  • Moisture and poor electrical contact, which may cause intermittent responses. Similar symptoms may also be caused by a fault outside the switch itself.

Informazioni aggiuntive

Peso 0.3 kg

Se non diversamente indicato nella descrizione, tutte le foto sono a scopo illustrativo.

Ci riserviamo il diritto di sostituire la referenza ordinata con la referenza sostitutiva indicata dal produttore.

I ricambi provengono da veicoli sinistrati, sono accuratamente controllati e offriamo su di essi una garanzia di funzionamento per 12 mesi.