Volante Citroën Peugeot 98210210ZD

Descrizione

Steering wheel for Stellantis vehicles
Leather-wrapped, in very good condition
Airbag connector is damaged

Part description

Used leather steering wheel for Citroën Peugeot, part number 98210210ZD is a suitable choice when replacing a worn or damaged steering wheel with a matching version. According to the description provided, the leather covering is in very good condition, which you will appreciate both in everyday driving and when refreshing the interior.

Important notice: the airbag connector is damaged. This part is therefore not intended for immediate installation without an expert assessment of this fault. Before use, the fault must be safely rectified using the procedure specified by the vehicle manufacturer. The extent of the connector damage and how it should be repaired are not specified in the documentation.

When selecting the part, compare the number 98210210ZD, design, mounting points and electrical connections with the original steering wheel. A matching model name alone is not enough to confirm suitability for a specific vehicle configuration.

Technical information

• Manufacturer: not specified; the Stellantis group is mentioned in the documentation.
• Model: Citroën Berlingo K9 | FIAT DOBLO III | OPEL COMBO E K9 | PEUGEOT RIFTER | Toyota ProAce City — designations taken from the product labels.
• Part type: steering wheel.
• Covering: leather.
• Condition: used, described in the original listing as being in very good condition.
• Reported fault: damaged airbag connector.
• Other numbers: not specified.

Product codes

• Product codes: 98210210ZD.

The product number is the primary reference when looking for this steering wheel. Before ordering, compare it with the marking on the original part and also make sure the design matches.

Installation recommendations

The following applies generally to this type of part: replacing a steering wheel involves working near the airbag system. The exact removal procedure, securing the steering wheel and safely disconnecting the system depend on the specific model and vehicle configuration. The following is a general overview, not a substitute for the manufacturer’s service procedure. Because the connector is reported as damaged, have it assessed and the installation performed by a professional with experience in airbag systems.

1) Before installation

• Compare the product number, shape and mounting points of the steering wheel, airbag connection and any controls with the original part.
• Inspect the rim, covering, seams, center and mounting sections. Check for visible cracks, deformation or loose parts.
• Have the damaged connector, its locking mechanism and associated wiring professionally assessed. Do not force or temporarily connect a damaged connection.
• Obtain the service procedure for the specific vehicle, including the conditions for reusing fasteners.

2) Tools and materials required

• Suitable hand tools for the specific steering wheel configuration and non-damaging removal tools.
• A torque wrench for tightening to the manufacturer’s specification.
• Diagnostic equipment suitable for checking the vehicle’s airbag system.
• A clean work surface and materials to protect the interior.

3) Step-by-step installation procedure

1. Secure the vehicle against movement and position the wheels and steering wheel straight ahead as specified in the service procedure.
2. Switch off the ignition, disconnect the battery as specified and observe the waiting period prescribed by the manufacturer before working on the airbag system.
3. Have the airbag module released professionally using the procedure specified for the particular configuration. Do not pry at unfamiliar clips or pull on wires.
4. Disconnect the relevant connectors after releasing their locks. Remove and store the airbag in accordance with the manufacturer’s safety instructions.
5. Record the position of the original steering wheel and the wiring route. Make sure the contact ring does not rotate out of its specified position during removal.
6. Release the fastener and remove the original steering wheel using the appropriate method, without striking it or applying excessive force to the steering column.
7. Compare the two parts again. Proceed only if the replacement steering wheel has been confirmed as suitable and the connector fault has been professionally rectified in accordance with the manufacturer’s procedure.
8. Fit the replacement steering wheel in the correct position, route the wiring without pinching it, and tighten the fastener according to the vehicle service specifications.
9. Connect the appropriate connectors and check that their locks are secured. Install the airbag module using the specified procedure.
10. Restore the power supply according to the manufacturer’s procedure and perform diagnostic and functional checks before putting the vehicle into service.

4) Post-installation checks and function verification

Check that the steering wheel is securely mounted, correctly positioned and that the steering operates smoothly without unusual noises. Check the horn and any controls for correct operation. The airbag warning light must behave as specified by the manufacturer, and the diagnostic check must not show any unresolved fault related to the installation. Only carry out a test drive after the safety of the steering and airbag systems has been successfully verified.

5) Common installation errors and how to avoid them

• Temporarily repairing a damaged connector: do not bridge contacts or improvise a replacement for the locking mechanism. Follow an approved repair procedure.
• Testing airbag circuits with unsuitable equipment: do not use a standard test lamp or multimeter on pyrotechnic circuits; leave the inspection to a professional.
• Rotating the contact ring: keep it in its specified position throughout the replacement.
• Pinched wiring or an unsecured connector lock: check the wire routing and that the connections are locked before completing the installation.
• Tightening by guesswork: use a torque wrench and the service specifications for the specific vehicle.

Reasons why parts become damaged

In general, steering wheel leather coverings wear due to frequent use, exposure to perspiration and sunlight, or unsuitable cleaning products. Rings and other sharp objects can also damage the surface and seams.

Connectors and their locks can be damaged by careless removal, pulling on the wiring or forcing the connection. Structural parts of the steering wheel may be damaged by impact or improper handling. The specific cause of the damage to this unit’s airbag connector is not stated.